ProjectorSupport - ViewSonic Global

How to Upgrade the M1+ Firmware?

<Notice> The firmware of M1+ will not be used on M1+_G2/_V or M1+ -2. 1. Go to “Downloads” -> ”Driver & Software” by searching M1+ from ViewSonic website to download “M1+ Firmware Update v2.03”. 2. Unzip the downloaded files and copy the Firmware files, “MstarUpgrade.bin" and "M1+WW.bin” to a FAT32 formatted USB drive. 3. Po...

Why am I unable to do wireless casting from my laptop via PJ-WPD-700?

For wireless casting via PJ-WPD-700, it's necessary to connect to an USB-C port of laptop/desktop which supports DP Alt mode (DisplayPort Alternative Mode on USB-C). USB Type C refers to the connector type, but not the capability of the port itself. Also, not all USB Type C ports support video output (Video over USB Type C). USB-C ports...

What is the duration of Security Update Support for ViewSonic Consumer Projectors?

ViewSonic will offer security update support to the following consumer projector products in compliance with the UK’s Consumer Connectable Product Security Regime and the Australian Cyber Security Act 2024 until the dates specified below. Product End of Support PX749-4K/ VS19349/ CPB414K/ HC4K41/ T4K41/ K414K/ V414K/ PX749-4KE/ PX74...

Why does my projector turn on and then suddenly shut off?

Automatic shutdown is usually triggered by overheating protection, power-saving settings, or lamp compatibility issues. Check the LED indicator lights for diagnostic clues. Troubleshooting Steps: Check LED Indicators: Temp Light (Red): Indicates overheating. Ensure vents are clear and fans are running. Let the unit cool for 30 minute...

What should I do if the projector remote control is not working?

Replace the batteries and ensure there are no obstructions between the remote and the projector's IR receiver. Replace Batteries: Insert a fresh set of batteries. Low power can cause intermittent operation even if the remote’s indicator light turns on. Clear Obstructions: Ensure the [IR Receiver] on the projector is not blocked by any ...

Why iPhone’s Mobile hotspot is not connecting with M2?

If you have problem connecting to hotspot on M2, Toggle your mobile hotspot (ON -> OFF -> ON). Toggle Wi-Fi option on the projector (ON -> OFF -> ON). Restart your iPhone and try connecting M2 to Mobile hotspot.

Why Can't I Power Off the Projector via its Remote Control?

For Models: PA/PG/PX Series “Power On” and “Power Off” are separated as two (2) different buttons on the remote control. This is different from the PJD series.

What to do if I can't mirror my screen after I updated the iOS version to iOS14?

Due to iOS14 compatibility issues, please follow below table for solution. Model Solution X100-4K Install EAirPlay.apk and follow instruction X10-4K Update FW to V1.13 via OTA M2 Update FW to V1.0 via OTA M1+_G2/M1+_V Update FW to V1.04 via OTA M1 mini plus Update FW to V1.02 via OTA SOP URL: https://support.viewsonic.com/hel...

What are the formats and maximum size do the USB and MicroSD reader on the LED projector support?

Please see the table below: Supported Size (Max. Size) NTFS Format FAT32 Format Read Write Read Write USB Memory Stick 256 GB V N/A V V USB HDD 2 TB V N/A V V Micro SD 256 GB V N/A V V Note: 1. Windows 10 built-in format tool only supports FAT32 format up to 32 GB. 2. Firmware upgrade only supports FAT32 format.

How to do Crestron E-control workaround due to Adobe Flash player not being supported?

Step 1 Download and install a Flash Player. “Download the Flash Player projector” from Adobe: https://www.adobe.com/support/flashplayer/debug_downloads.html Step 2 Input the URL of the Crestron interface in the Flash Player: http://[projector.ip]/CrestronUI.swf Where [projector.ip] is the ViewSonic projector’s IP address.