ProjectorSupport - ViewSonic Europe

What to do if I can't mirror my screen after I updated the iOS version to iOS14?

Due to iOS14 compatibility issues, please follow below table for solution. Model Solution X100-4K Install EAirPlay.apk and follow instruction X10-4K Update FW to V1.13 via OTA M2 Update FW to V1.0 via OTA M1+_G2/M1+_V Update FW to V1.04 via OTA M1 mini plus Update FW to V1.02 via OTA SOP URL: https://support.viewsonic.com/hel...

What should I do if the projector remote control is not working?

Replace the batteries and ensure there are no obstructions between the remote and the projector's IR receiver. Replace Batteries: Insert a fresh set of batteries. Low power can cause intermittent operation even if the remote’s indicator light turns on. Clear Obstructions: Ensure the [IR Receiver] on the projector is not blocked by any ...

Why am I unable to do wireless casting from my laptop via PJ-WPD-700?

For wireless casting via PJ-WPD-700, it's necessary to connect to an USB-C port of laptop/desktop which supports DP Alt mode (DisplayPort Alternative Mode on USB-C). USB Type C refers to the connector type, but not the capability of the port itself. Also, not all USB Type C ports support video output (Video over USB Type C). USB-C ports...

What is the duration of Security Update Support for ViewSonic Consumer Projectors?

ViewSonic will offer security update support to the following consumer projector products in compliance with the UK’s Consumer Connectable Product Security Regime and the Australian Cyber Security Act 2024 until the dates specified below. Product End of Support PX749-4K/ VS19349/ CPB414K/ HC4K41/ T4K41/ K414K/ V414K/ PX749-4KE/ PX74...

How to set up dual projectors on a Windows computer?

Before connecting two projectors to your Windows PC/laptop, please ensure your system can run multiple video outputs. 1. To check your graphics card's maximum number of output signals, please refer to the graphics card manufacturer like the example below. Dedicate Graphics Card Integrate Graphics Card 2. Make sure your devi...

Why is my projector fan making an unusual noise?

Most fan noise issues are related to settings or ventilation. Check the High Altitude Mode and ensure the vents are clear before considering repair. Troubleshooting Steps: Verify Device Specs: If you own a fanless portable model and hear strange noises, contact support immediately as there are no moving parts intended to make sound....

How to purchase a lens for a projector

Or browse to your projector model in the Projector Accessories section of the ViewSonic Store. If a Long Throw lens is available for your projector, it will be listed on the online store. Note: A Long Throw Lens is not available for all ViewSonic projectors. To check availability, or to purchase a long throw lens, please contact ViewSonic...

How to fix the keystone effect (distorted image) on a projector?

Ensure the projector is level and perpendicular to the screen, then use the built-in "Keystone" settings to square the image. When you see below situation, please follow below instructions to adjust: Physical Alignment: Place the projector on a flat surface. Ensure the lens is at a 90-degree angle relative to the center of...

Why does my projector automatically shut down during use?

Auto-shutdown is typically triggered by overheating protection. Ensure proper ventilation, clean the dust filters, and enable "High Altitude Mode" if necessary. Check LED Indicators: If the Temp light is red or flashing after shutdown, the projector has overheated. Improve Airflow: Keep at least 50cm of clear space around intake an...

How to change the projector image orientation (Flip or Mirror image)?

Access the "Projector Position" setting in the system menu to adjust the image based on your installation (Desktop, Ceiling, or Rear projection). Open Menu: Press the [Menu] button on your remote or projector. Navigate to Settings: Go to [System Setting: Basic] > [Projector Position]. Select Orientation Mode: Choose the option that ...